Not sure if we can post direct link on the forum for reseller, but if you look for ridata mini dvd-r on eBay you should find some, they usually sell them in pack of 10, 50, 100, most are free shipping to the state, the seller I choose specified in the description that the media code was RITEKG04.

You should find everything in that topic viewtopic.php?f=26&t=666

I found that on the web last month https://www.youtube.com/watch?v=vSUH3krCbmA This Is what you should not do!!!, You'll need to use a rotary tool like a dremel, the video can give you a preview where to cut, you can cut the outer egde on the left and right to make it easier to insert a disc but wit...

Didn't receive my chip yet, but I XenoPi'ed my GC (thanks Streetwalker for the file and complete guide) and it's booting 4 back up on 4, I used full size Philips DVD-R 16x (waiting for some RitekG04) burned at 4x(min. I could...) with imgburn on my LG GSA-4167B that I upgrade the fw to DL13. pot was...

^Congrats! So here's a DigiKey BOM for all of the components I could gather, minus the PCB: U1 122-1594-ND (Supports OSD) U2 557-1583-5-ND U3 AP1117E50GDICT-ND U4 1028-1069-1-ND (1.5A rating to support SPDIF) CONN2 WM19088CT-ND C1 thru 6 399-1170-1-ND (not sure if suitable for C5 & C6) C7 478-3...

Thanks for the info, and also for being active a lot on the forum.

Apply the switch to the CS pins, not the 3.3v line :) I thought to use the chip select signal, but if I break only CS and and the front slot is selected with the switch with no card inside, sense will still be HIGH from the sd card detect. That's why I thought cutting the power to one or the other ...

Hello guys, so I'm currently waiting a xenoGC chip, but for fun I decided to open my cube to put a region switch on R5 for jap/usa. Everything went fine, I can now boot both. But just after I removed the heat sink to access to the circuit board, I did realize that normally when removing a heat sink,...

Hello guys, I've just order a xenoGC for my cube with some ritekG04 and I'll make a SDgecko adapter. Now I'm looking information for a known working burner with ritek mini dvd-r. All I got is an old Lg GSA-4167B ver.DL11 that I use with a ide to usb adapter on my computer. I didn't use it that much ...

So only one card in slot B is use, but I want to leave both card inserted and only switch from sd to memory card when I desire, leaving both connected at the same time on the same pin, the GC would send data to both and also read from both(would make probably errors). But I understand what you want ...

emu_kidid wrote:Seriously guys - just go to badassconsoles.com you will not get any better service when it comes to WASP Fusion.

Currently out of stock, did check before asking...

Don't answer all at the same time! I did a schematic on my free time to explain how I would proceed. SD_Adapter.jpg I would cut the vcc trace that go to each memory slot, and would power them with a 1P2T switch to choose if I want to power the front slot or the sd adapter. From what I understood fro...

Did you found it online? I'm looking for one too.

Good luck for your project!

thanks

Hello, I just pull out my old gamecube and I decided to mod it a little, basicaly I ordered a XenoGC that I would solder it to run Swiss on a mini-dvd. I saw picture of a guy who instead of making a SdGecko adapter, he solder it right on a memory slot of the GameCube. I'm new to hardware mod on a ga...