Search found 15 matches
- Sun Jul 30, 2017 1:28 am
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
After trying the same procedure on Windows 10 it worked on the first try. Something was borked with my Windows 7 Machine in combination with my Hardware. Don't know what it was, but now it works and i can add it to my build
- Fri Jun 02, 2017 5:01 pm
- Forum: Hardware / Modding
- Topic: 3D Printed Solution to make a slimmed Wii Drive Top loading
- Replies: 2
- Views: 3436
Re: 3D Printed Solution to make a slimmed Wii Drive Top loading
I'm on it.Diminuendo wrote:Images don't seem to be loading
Thanks for the notice.
- Fri Jun 02, 2017 4:12 pm
- Forum: Hardware / Modding
- Topic: 3D Printed Solution to make a slimmed Wii Drive Top loading
- Replies: 2
- Views: 3436
3D Printed Solution to make a slimmed Wii Drive Top loading
Hey there, I'm in the Process of making my own Gamecube Portable. Since i use a slimmed Wii Drive for the form Factor, i found no solution on how to install a top loading Spindle. So here's what i came up with: 1. I bought some Laptop DVD Drives. I got 2 in my Area for 10€ total (5€ each) and consid...
- Sat Jan 21, 2017 9:00 pm
- Forum: Hardware / Modding
- Topic: Cloning the GameCube component cable
- Replies: 723
- Views: 602159
Re: Cloning the GameCube component cable
Alright so I have compiled my first board. However I have zero experience in programing a FPGA board. When I use the regular programming mode with the .jed file I get this error: Device#1 LCMXO2-640HC: Failed to verify the ID (Expected: 0x012B9043 Read: 0x00000000). ERROR - Check configuration setu...
- Fri Jan 20, 2017 12:19 am
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
Little update. Got a genuine Lattice and Xilinx Programmer from a friend and the same Error persists. I have soldered my 3rd board now and im 100% sure the Parts are not the issue. I took a microscope to check if there any bridges or floating pins. There are none. Every Software i tried just detects...
- Wed Jan 18, 2017 11:18 am
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
The cable is detected properly and the LED is blue when i add 3V to the Board. If i Remove the voltage the LED goes red.
My Jtag order is this : VCC, Tms, tck, tdi, tdo, gnd. Is that correct?
Its most probably a software error but i dont have access to another computer to test it.
My Jtag order is this : VCC, Tms, tck, tdi, tdo, gnd. Is that correct?
Its most probably a software error but i dont have access to another computer to test it.
- Tue Jan 17, 2017 10:24 pm
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
The FPGA is receiving power on all rails like it should be (3.3V directly from the Gamecube Regulator Board). After the renewal of my board i am now 1 step further. Now i get a "Identify Succeeded" on the Workspace. The Workspace stays Empty though. You shouldn't need to load a BSDL file ...
- Mon Jan 16, 2017 4:54 pm
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
Little Update, I just reinstalled Windows and all Drivers needed and ordered a new Programmer, since the other one wont turn on anymore. Lets see if it was the programmer.
- Fri Jan 13, 2017 11:27 am
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
Yay, atleast some progress :D I have a new Problem now. After i rebooted my PC due to an Update cause i could not stand that popup by windows any longer, the device count detected is random. I get 3 devices then 12 then over 30 and so on. I will take my usb microscope and check for bridges again and...
- Thu Jan 12, 2017 10:07 pm
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Re: Problem at Programming GCVideo lite
The FPGA is receiving power on all rails like it should be (3.3V directly from the Gamecube Regulator Board). After the renewal of my board i am now 1 step further. Now i get a "Identify Succeeded" on the Workspace. The Workspace stays Empty though. I downloaded the BSDL File from Lattice ...
- Tue Jan 03, 2017 11:35 pm
- Forum: Hardware / Modding
- Topic: Cloning the GameCube component cable
- Replies: 723
- Views: 602159
Re: Cloning the GameCube component cable
After selecting the BSDL file, a "Device Programming Properties" dialog pops up which will most likely be almost completely empty. Just hit OK which should give you access to the main workspace showing the JTAG chain with just one device in it. Not the Case for me. I get like 30 unknown d...
- Tue Jan 03, 2017 3:53 am
- Forum: Support
- Topic: Problem at Programming GCVideo lite
- Replies: 10
- Views: 9692
Problem at Programming GCVideo lite
Hello GCF-Community, I have all the Parts together to make my first Gamecube Portable in Combination with my newly built 3D Printer. Since a few Days im trying to get my freshly soldered gcvideo lite board working. I had an Xilinx Programmer lying around and thought to myself: " well that shoul...
- Tue Dec 27, 2016 3:47 am
- Forum: Hardware / Modding
- Topic: Cloning the GameCube component cable
- Replies: 723
- Views: 602159
Re: Cloning the GameCube component cable
In case anyone is interested in an updated Parts list i attached one from Mouser Electronics. All Parts cost roughly 16$ (without shipping).
Click Me
I included the Designators of the Board so its clear where every Part goes.
Click Me
I included the Designators of the Board so its clear where every Part goes.
- Sun Nov 13, 2016 12:46 am
- Forum: Hardware / Modding
- Topic: Commission for Gintoki - GameCube Fusion Rev. 2
- Replies: 32
- Views: 21945
Re: Commission for Gintoki - GameCube Fusion Rev. 2
The Batteries are LG LGABB41865 18650 2600mAh in case someone wants to know.
- Tue Nov 01, 2016 10:49 pm
- Forum: Hardware / Modding
- Topic: minGC Controller Board
- Replies: 61
- Views: 43343
Re: minGC Controller Board
I know I'm a little late to the party, but i recently started building a Gamecube Portable and i wanted to ask if there are any boards left.