Search found 8 matches
- Fri Feb 08, 2019 11:19 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
Gave it a try with the SD card in the WASP, no luck still. Was worth a shot!
- Tue Feb 05, 2019 9:45 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
I did not. I was unaware that it needed to be in there for the test to run properly.Streetwalker wrote: ↑Sun Feb 03, 2019 10:45 pmJust to make sure, you did have an SD card in the wasp when you ran that test right?
I'll give it a try again in a little bit here with one in there.
- Sun Feb 03, 2019 3:11 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
I'm well aware of how it's designed, but it's happened before. It's also possible that you didn't push it in all the way, leaving the connector inserted at an angle which can cause a wrong connection. At any rate, I know mega tends to be anal with testing and packages things well, in antistatic bag...
- Sun Feb 03, 2019 2:53 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
It just hangs.
- Sun Feb 03, 2019 2:09 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
The devices were thoroughly tested before shipping. If it's not working then we can only assume that you've done something wrong like plugging it in incorrectly, which could have damaged the FPGA by feeding 5V into fragile IO pins. You can confirm this by running the attached dol. Swap the wasp in ...
- Sun Feb 03, 2019 6:45 am
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
Well, at 4 months with no ideas from the forum or BAC, I'm going to assume I was just sold a dud and there's nothing to do about it. Super disappointed in both the product and the company that sold it to me.
- Wed Jan 09, 2019 6:29 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
Re: WASP Custom from BAC seemingly non-working
Managed to get hold of another, already modded Gamecube to try and re-flash the firmware on the WASP. This is the screen i get after loading the FZN file from an SD gecko while the WASP is installed https://imgur.com/a/LPn962Y The red LED is solid on the device, and the gamecube goes unresponsive. I...
- Fri Nov 02, 2018 4:38 pm
- Forum: Modchips
- Topic: WASP Custom from BAC seemingly non-working
- Replies: 11
- Views: 18172
WASP Custom from BAC seemingly non-working
Hopefully someone here can tell me that I'm the issue and the item is fine! I bought a WASP back in July, got it in September, tried to install it two weekends back. It does not seem to work. It just boots up to the "An error has occurred. Turn the Power Off and check the Nintendo GameCube Inst...