Search found 90 matches

by dilav
Tue Feb 09, 2021 10:57 am
Forum: Wii
Topic: WII open source modchip Hex files
Replies: 4
Views: 2515

Re: WII open source modchip Hex files

IIRC a lot of downloads were in forums requiring logins so I'm not sure how much the wayback machine has. The wayback does have sksapps archived though, and there is a active torrent of sksapps downloads section available as well. https://web.archive.org/web/20100102003949/http://sksapps.com/index.p...
by dilav
Tue Feb 09, 2021 10:38 am
Forum: Hardware / Modding
Topic: GCHD Mk2 - upgrading firmware
Replies: 6
Views: 3161

Re: GCHD Mk2 - upgrading firmware

Make sure the driver is installed and try different versions of the software. I have heard some software doesn't seem to work as well for some. Also note to use the pin header on the CH341A programmer, as some of the software will have the chip orientation flipped on the socket due to (probably diff...
by dilav
Fri Feb 05, 2021 8:55 am
Forum: Wii
Topic: WII open source modchip Hex files
Replies: 4
Views: 2515

Re: WII open source modchip Hex files

Check sksapps archives, they mirrored a bunch of files including a few open source Wii chip codes.
by dilav
Wed Sep 16, 2020 4:58 am
Forum: Hardware / Modding
Topic: IPL settings (language and clock) are not getting saved. Battery already replaced
Replies: 8
Views: 1749

Re: IPL settings (language and clock) are not getting saved. Battery already replaced

Clean the areas with isopropyl alcohol before trying to take measurements. The battery is connected to Pin 1 of the front panel socket. Ensure you are getting battery voltage on the circle test point under R16 (might be R15?, it's left of C74). R16 looks dodgy. It should have low resistance, a few h...
by dilav
Mon Aug 10, 2020 8:36 am
Forum: Hardware / Modding
Topic: GCHD Mk2 - upgrading firmware
Replies: 6
Views: 3161

Re: GCHD Mk2 - upgrading firmware

Bridge JP1 to disable.
J2 header is SPI.
In the following order (Parentheses = Silk Screen):
(J2) MOSI CLK MISO CS 3V3 GND (CON2)
by dilav
Wed Jan 29, 2020 8:48 am
Forum: Modchips
Topic: New IPL replacement modchip: HyperBoot
Replies: 27
Views: 10310

Re: New IPL replacement modchip: HyperBoot

I had a email from him the other day. Firmware 1.1 supports SD2SP2. There's also a version 2 of the chip that has some extra storage space for dol storage. I haven't played with it or know much about it though.
by dilav
Wed Jan 22, 2020 5:40 am
Forum: Modchips
Topic: IPLBoot on XenoGC
Replies: 3
Views: 4254

Re: IPLBoot on XenoGC

But a DIY build XenoGC with a bigger flash memory, would that work then?? It's source code is release so you could, but there's not much point as it's a drive chip so it probably can't boot anything unless there's a disc in the drive. You're better off developing a IPL replacement chip or just wait...
by dilav
Wed Jan 22, 2020 5:33 am
Forum: GameCube
Topic: I can launch SWISS but can't launch any games. What am I doing wrong?
Replies: 12
Views: 2933

Re: I can launch SWISS but can't launch any games. What am I doing wrong?

That's hilarious, glad you figured it out.
by dilav
Fri Jan 17, 2020 4:40 am
Forum: Hardware / Modding
Topic: GCPlug Information - Inc firmware updates
Replies: 42
Views: 9582

Re: GCVideo 3.0a for Chinese GCPlug ?

It's really clever, you can put the device into update mode from the OSD. Then you run the updater.dol - this homebrew actually encodes the new firmware into the video signal. The FPGA grabs the new code and updates the firmware. I think I recall some very early component to HDMI adapter dongles fo...
by dilav
Thu Dec 26, 2019 1:42 am
Forum: Hardware / Modding
Topic: Could someone help me convert mcs to bin
Replies: 2
Views: 1125

Re: Could someone help me convert mcs to bin

HDMy Cube regular/Pro are both gcplug PCBs but with different casing. The pin def are available on citrus' github. HDMy Cube worked with insurrection industry on their component cable and are still somewhat active on twitter. You're going to have to build or ask someone with the build environment se...
by dilav
Sun Dec 15, 2019 8:07 am
Forum: Hardware / Modding
Topic: Hi, about Serial port 2 USB for Swiss, any chance?
Replies: 106
Views: 36714

Re: Hi, about Serial port 2 USB for Swiss, any chance?

BimboBoop wrote:
Sun Dec 15, 2019 6:25 am
Sorry guys, I didnt knew about IPLboot, so this version can boot SWISS using just the new SDSP2 board?
No, you need IPL modchip like Qoob, Viper, Hyperboot (If it gets updated for SP2)
by dilav
Sat Nov 30, 2019 11:29 pm
Forum: Hardware / Modding
Topic: GameCube Memory Card & SD Gecko Diagrams
Replies: 56
Views: 85920

Re: GameCube Memory Card & SD Gecko Diagrams

Hi, i'm looking for the pads where to solder a SD2SP2 on a DOL-101, but to begin, I'm not able to find somebody that did it for a DOL-001. Nor can I find the bare motherboard and inside layers pics in hires to track the routing by myself. Maybe somebody already figured out where the SP2 port is at ...
by dilav
Sat Nov 02, 2019 12:11 am
Forum: Homebrew & Utilities
Topic: CleanRip v2.1.1
Replies: 20
Views: 9865

Re: CleanRip v2.1.0

Thanks everyone involved. I wonder what practical use dumping Datel discs has, though. There was a thread a while back where someone was trying to dump Datel Advance Game Port disc, a boot disc for Datel's accessory to play GBA game carts through emulation instead of hardware like the official Game...
by dilav
Thu Oct 17, 2019 12:25 am
Forum: Support
Topic: Disc Backup causing disc read error.
Replies: 11
Views: 5440

Re: Disc Backup causing disc read error.

There's a new problem these days with capacitors needing replacement on the DVD PCB, have run into 2 where even a laser from a new GameCube swapped over wouldn't work, but when the caps were replaced it worked fine Any specific capacitor that is causing the issue or do you just replace all electrol...
by dilav
Thu Oct 17, 2019 12:19 am
Forum: Hardware / Modding
Topic: received this the other day
Replies: 6
Views: 3086

Re: received this the other day

Print quality looks meh, it is very cheap though especially for all the work in assembling that.
by dilav
Fri Sep 06, 2019 4:28 am
Forum: Hardware / Modding
Topic: How do I update the Pluto 2 HDMi Board?
Replies: 1
Views: 1547

Re: How do I update the Pluto 2 HDMi Board?

You need KNJN's TXDI programming board or a JTAG programmer. Take a look at KNJN's documentation and gcvideo's documentation.
by dilav
Wed Sep 04, 2019 4:33 am
Forum: Hardware / Modding
Topic: Lost USB programmer board for Qoob Pro
Replies: 6
Views: 3157

Re: Lost USB programmer board for Qoob Pro

EDIT: Also, am I right in thinking that with the USB board attached to the main board (as in your pictures), the LED on the USB board doesn't function? It only works with the FFC attached? I believe you are correct. I did not see any other traces besides the 4 usb points that snakes their way acros...
by dilav
Sun Sep 01, 2019 1:56 pm
Forum: Hardware / Modding
Topic: Lost USB programmer board for Qoob Pro
Replies: 6
Views: 3157

Re: Lost USB programmer board for Qoob Pro

I uploaded photos here:
https://imgur.com/a/tMTxcRh

You are going to have to trace the chip side yourself.
by dilav
Sun Sep 01, 2019 12:40 pm
Forum: Hardware / Modding
Topic: Hi, about Serial port 2 USB for Swiss, any chance?
Replies: 106
Views: 36714

Re: Hi, about Serial port 2 USB for Swiss, any chance?

I didn't mean to imply anyone is saying the design is bad. I just mean to say that I think the design choice is good and just voicing my opinion. Assembling two boards together isn't exactly hard, but I was thinking in terms of a design that is made for sale. Having two boards will require some hand...
by dilav
Sun Sep 01, 2019 1:43 am
Forum: Hardware / Modding
Topic: Hi, about Serial port 2 USB for Swiss, any chance?
Replies: 106
Views: 36714

Re: Hi, about Serial port 2 USB for Swiss, any chance?

The form factor doesn't suit me, neither the extenders, as you stated, so i'm gonna try to make a home-made one, to try at first, until an angled one is available (if I'm too slow to design one myself). I think it is a good design, but of course others will have different opinion. The microSD slot ...
by dilav
Fri May 24, 2019 3:23 pm
Forum: GameCube
Topic: Where to buy WASP Fusion flex ribbon cables ?
Replies: 5
Views: 4363

Re: Where to buy WASP Fusion flex ribbon cables ?

Wii Drive / Fusion ODEs are the same spec 0.5mm pitch, same side contact, but with 32 connectors.
by dilav
Tue May 07, 2019 7:50 am
Forum: Hardware / Modding
Topic: Codejunkies SD Media Launcher Issues
Replies: 4
Views: 3933

Re: Codejunkies SD Media Launcher Issues

It's been mentioned a few times, but if you're looking for non-SDHC 4GB cards check the TOPRAM brand. You can find them in listings called "TOPRAM 4GB non-HC" or "TOPRAM 4GB non-SDHC". Doesn't really matter if you pick up any 2GB or smaller either and you can always swap to SDHC after booting into s...
by dilav
Wed Aug 08, 2018 12:00 pm
Forum: Hardware / Modding
Topic: I want to make duplicates of Panasonic Q parts...
Replies: 3
Views: 3310

Re: I want to make duplicates of Panasonic Q parts...

I'm not familiar with Panasonic Q, or the ability/quality of cast-ed parts, but Rose colored gaming has some SLA 3D printed replacement rails. I believe it's the same rails you guys are talking about. Quite expensive IMO, but might give those who are looking at this some ideas, and possibly differen...
by dilav
Sat Jun 09, 2018 1:52 am
Forum: Swiss
Topic: Swiss Nightly Build
Replies: 822
Views: 492132

Re: Swiss Nightly Build

I can't seem to get the Swiss to load. I bought an SD Media Launcher from Datel. It's been known that the SDML adapter it comes with is crap and doesn't get recognize. The 2GB card should work, make sure it's FAT formatted, try the tape fix by putting a piece of tape under the circuit board of the ...
by dilav
Wed Apr 11, 2018 7:04 am
Forum: GameCube
Topic: Do Gamecubes (DOL-001) without Digital AV exist?
Replies: 6
Views: 4719

Re: Do Gamecubes (DOL-001) without Digital AV exist?

It's definitely a case swap, the rear panel color is supposed to match the rest of the console. I'm not saying this statement is wrong, DOL-001 had matching rear panel color (at least the common colors ones). But I don't recall seeing a platinum(silver) or indigo(purple) rear panel color on the DOL...