Hi, about Serial port 2 USB for Swiss, any chance?

Portables, case replacements, mods etc, all in here!
gckrz
Posts: 5
Joined: Mon Apr 13, 2020 8:04 pm

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by gckrz » Mon Apr 20, 2020 11:15 am

Papy.G wrote:
Mon Apr 20, 2020 9:37 am
Just do not use outdated SWISS releases, always keep up to date so you'll get the better from it. :roll:
775-1 was the latest release at the time I received the board and burnt the disk :?
Papy.G wrote:
Mon Apr 20, 2020 9:37 am
Pin assignment is quite straightforward:
SP-SD
VCC-VCC
GND-GND
CS-CS
CLK-CLK
MOSI-MOSI
MISO-MISO

Beware, if MISO and MOSI are labelled DI/DO, you'll have to cross the wires so that it will be:
DO-DI
DI-DO
I will check that, maybe my mate rerouted some traces (but I doubt so).
I3lackcloud
Posts: 3
Joined: Fri Apr 24, 2020 7:47 am

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by I3lackcloud » Fri Apr 24, 2020 8:07 am

Hi there,

excuse me my shabby english, it is not my mother language. ;)

I own a Gamecube with a qoob pro. As bios i use iplboot to boot directly from the sd-gecko in slot B. In the next weeks i will receive all parts for a sd2sp2 and i want to replace the sd-gecko with it. As i read in some threads, iplboot was not able to boot a dol from sd2sdp2. But PapyrusWithCheesy added some code, with which iplboot should be able to boot from sd2sp2, as found here:

https://github.com/redolution/iplboot/c ... 124c9a2e71

A few sites previously in this thread i read, that this ended in a green streaked screen.
Is this particular error now fixed? I would be very concerned, if it is possible to replace the sd-gecko completly with the sd2sp2.

Thank you!
User avatar
Papy.G
Posts: 515
Joined: Mon Mar 04, 2019 6:14 am
Location: France, Occitanie
Contact:

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by Papy.G » Fri Apr 24, 2020 8:48 am

The site says all, it supposedly just need to be recompiled with devkitPPC r26, everybody is stuck now for the chips with lesser memory, the confirmed working IPLboot is as big as 15 blocks at the moment, 10 blocks compressed, but it hasn't been confirmed working on any chip, one block is 8KB, see for yours.

Totally replacing the SDGecko is not a real good idea anyway, as many utilities are not ready for the SD2SP2, some emulators hadn't been maintained for a long time, for example.
DMG/MF OC, AGB/SC miniSD, NTR/NeoMK3, USG/flashme V8/SC miniSD
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD

Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
I3lackcloud
Posts: 3
Joined: Fri Apr 24, 2020 7:47 am

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by I3lackcloud » Fri Apr 24, 2020 9:39 am

Thank you for your replay!

I am not sure, if i understand you correctly. Is there a working version for chips with larger memory as the qoob pro (2MB)? And do the problem only exists for chips with lesser memory like the SX (128kb)?
Or is there no compiled version at all at this time and i have to wait a bit longer until someone could compile the code?

I don't use any other applicatione (like emulators etc.) than swiss. Swiss for me is only for outputting 480p and play some backups from the sd card.
brunops3
Posts: 48
Joined: Mon Feb 06, 2012 5:24 pm

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by brunops3 » Sun May 17, 2020 1:26 am

Hi guys.

I really hope someone post here the compressed dol/vgc files (< 128 kb) of the latest revision of iplboot (with SD2SP2 support) for using with the Viper GC (not Extreme).

Thank you.
I3lackcloud
Posts: 3
Joined: Fri Apr 24, 2020 7:47 am

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by I3lackcloud » Fri Aug 14, 2020 8:46 am

Are there any news on a new compiled iplboot for qoob pro with sd2sp2 support?
Did you found a way to compile with the devkitPPC r26?
User avatar
PlatypusWithCheese
Posts: 12
Joined: Thu Dec 12, 2019 11:59 am

Re: Hi, about Serial port 2 USB for Swiss, any chance?

Post by PlatypusWithCheese » Sun Sep 13, 2020 12:06 am

To compile iplboot with SD2SP2 support requires the latest devkitPPC(rolling release)
Compiled file will be too large for qoob SX, requires qoob Pro.
I will not compile it for you.
Here is a link to the repo https://github.com/redolution/iplboot NO LONGER MAINTAINED

This is roughly how you do:
PlatypusWithCheese wrote:
Fri Dec 20, 2019 3:16 am
if you are on debian/ubuntu

- Install latest devkitpro-pacman then run

Code: Select all

dkp-pacman -S gamecube-dev
- Install Clang and 32bit gcc libraries

Code: Select all

sudo apt-get install clang gcc-multilib
- Create Clang symlink

Code: Select all

ln -s /usr/bin/clang $DEVKITPPC/bin/powerpc-eabi-clang
- Locate PAL 1.0 IPL put it in the same directory as the makefile and name it ipl.rom
- Run make

but i do not know how to get it to output the viper gc file.
Sending me a PM about this will probably link you to this.
Indigo DOL-001(EUR)/GBP/BBA/RGB/qoob pro/SD2SP2
Post Reply