SD-load issues...
- R3dfaction
- Posts: 48
- Joined: Mon Apr 12, 2010 3:05 am
- Location: Florida, US
SD-load issues...
I burnt an iso with SD-Load and it runs the program but it does not load any dol's (or rather read them) on my Sd card via Wiikey Adapter. Is there something I'm doing wrong? I was also mentioned by emu_kidid to embed SD-Load it within the Cobra BIOS but I'm not unsure on how to accomplish that.
I have my dols on the root of the Sd cards (Tried with 2gb SD and 8 Gb Micro SD) and it just shows a blue bar. Any help would be appreciated...
I have my dols on the root of the Sd cards (Tried with 2gb SD and 8 Gb Micro SD) and it just shows a blue bar. Any help would be appreciated...
Dol-001 | RGB Cables | Viper GC Extreme | GB Player | BBA | XCM Crystal Case Light Mod
Re: SD-load issues...
Firstly, SDLoad won't work with SDHC cards (4GB and over in size basically) as well as some microSD cards, even if they're under 4GB sometimes.
If you're using the SlotA & B version of the DOL, make sure you've plugged the adapter into the correct slot (If you don't press A on startup, it's slot A, otherwise it's slot B).
Finally, make sure the contacts are clean on the wiikey SD adapter as they can be quite tempramental if they have even a spec of dust.
Hope this helps!
If you're using the SlotA & B version of the DOL, make sure you've plugged the adapter into the correct slot (If you don't press A on startup, it's slot A, otherwise it's slot B).
Finally, make sure the contacts are clean on the wiikey SD adapter as they can be quite tempramental if they have even a spec of dust.
Hope this helps!
- R3dfaction
- Posts: 48
- Joined: Mon Apr 12, 2010 3:05 am
- Location: Florida, US
Re: SD-load issues...
Tried both slots with the 2gb SD Card and still shows a blue line across, anything else I press ends up in a code dump, any other suggestions? Would embedding SD-Load in the BIOS make a difference (even I doubt it)?
Dol-001 | RGB Cables | Viper GC Extreme | GB Player | BBA | XCM Crystal Case Light Mod
Re: SD-load issues...
Ah.. you need FAT16! how could I forget :p
- R3dfaction
- Posts: 48
- Joined: Mon Apr 12, 2010 3:05 am
- Location: Florida, US
Re: SD-load issues...
Its in FAT so thats the probable cause, will attempt tommorrow thanks for the tip. Btw can you tell how to embed SD-Load on the Cobra Bios?
:L
:L
Dol-001 | RGB Cables | Viper GC Extreme | GB Player | BBA | XCM Crystal Case Light Mod
Re: SD-load issues...
Since you have a viperGC Extreme, just flash the .DOL onto the 2MB flash.
- R3dfaction
- Posts: 48
- Joined: Mon Apr 12, 2010 3:05 am
- Location: Florida, US
Re: SD-load issues...
???
I'm kind of a Noob, can you tell me step by step on how to do it? also I can't find an SD-Load.dol I only found the ISO, can someone upload it in the repository?emu_kidid wrote:Since you have a viperGC Extreme, just flash the .DOL onto the 2MB flash.
Dol-001 | RGB Cables | Viper GC Extreme | GB Player | BBA | XCM Crystal Case Light Mod
- R3dfaction
- Posts: 48
- Joined: Mon Apr 12, 2010 3:05 am
- Location: Florida, US
Re: SD-load issues...
bump... anyone???
Dol-001 | RGB Cables | Viper GC Extreme | GB Player | BBA | XCM Crystal Case Light Mod
Re: SD-load issues...
I can respond properly in a few days when I've got some time.
- R3dfaction
- Posts: 48
- Joined: Mon Apr 12, 2010 3:05 am
- Location: Florida, US
Re: SD-load issues...
Ok I've tried formatting my 2gb SD to FAT and it still shows a blue bar screen, please can someone help me? Is my SD Gecko defective?
Dol-001 | RGB Cables | Viper GC Extreme | GB Player | BBA | XCM Crystal Case Light Mod