Hi all, Been installing these boards for a little while now and these new boards do not require the 100ohm resistor. I have not had any luck getting these boards to work properly. The power light on the Pluto 2x flashes green as it should when wired correctly, but the video output will come on for a...

Hi all, i have a new Pluto 2x board that is revision E. I have wired it correct, and also shorted the jumper so you don’t need the resistor. I get audio and video for about 30 seconds to 1 minute. The video will keep playing, the audio will get garbled and distorted and then the audio goes out. The ...

Thanks for the reply! Which one should I be using in the archive? The compressed one or the Viper one?

Thanks.

Alright I hope this makes sense to someone who reads this and can give me a hand here. I flashed my ViperGC (non extreme) with the SD Load Slot B plugin. The plugin works fine when I load it up, I can see my SD card and load DOL files without issue. Now, when I load any version of Swiss using this m...

Is this worth upgrading my Viper GC to iplboot?
What are the advantages? Can I revert back to ViperGC OS?

Thanks

EDIT - Anyone have screenshots of this new bios in action?

Anyone know if these things will be available any time soon?

A little more digging reveals that using the ANALOG output on the GameCube plays no audio as well.

This is looking to be an actual gamecube MLB issue. Anyone have any insight as to where to start?

Thanks

I removed the board completely and resoldered it. I have done over 10 of these boards and have not ever experienced this before. Do you happen to know which pins exactly the audio is being routed from on the GC board as well as the pluto?

Hi all, I have an older Pluto board installed in a GameCube, its running version 2.4a. After wiring it up, im not getting any audio at all, even with Enhanced DVI mode enabled. i have tried different HDMi cables as well as different displays. Its only happening with this Pluto board, my other GameCu...

I have a Pluto 2 HDMI board installed in my gamecube. What parts do I need to perform the firmware update? Im currently on 2.4b and would like to have the latest FW installed.

Thanks in advance.

Extrems wrote:You can use it to load Swiss from the SD card, but there are other options that are even smaller.

How? What files do I need, can you elaborate?

Extrems wrote:Game Boy Interface is currently 29-33 blocks.

The GameBoy interface can load ISO's? Im trying to get Swiss loaded up to run ISOs from the SD card.

Alright, i was able to move over the exploit file, but the boot.gci, its too big to fit on the memory card, i have a 59 block memory card. And the smallest boot.gci i found was 1MB.

Extrems wrote:Nope. You need an actual GameCube Memory Card.

I have a GameCube Memory card and I have a GameCube memory card that accepts SD cards.....

Extrems wrote:An SD Card Adapter is not a GameCube Memory Card.

what in the world are you talking about????

I have a gamecube memory card that accepts SD cards, isn't that whats required?

Bump

Still not having any luck here.......keeps telling me "Another device is inserted......" and will not let it read the memory card....help....

Can anyone tell me how to set this up for the Splinter Cell Exploit? I have no clue where to start.
I have the files downloaded from the other post, just no idea what to do next.
Thanks

Can anyone post the exact files needed on the SD card to pull this off on a GameCube with an Memory card SD adapter?

Thanks.

I sent two private messages and they are in my outbox, I dont see them in the Sent folder. How do I get these messages to send?

Thanks

I have resolved the issue. Pin 94 from the Pluto board going to the GC motherboard was not making a good connection. Used the alternate solder point on the GC motherboard and the issue has been resolved.

Thanks again for the support.

Thread may be closed.

You forgot to mention something important. https://assemblergames.com/threads/gamecube-controller-port-1-not-working.68998/ The issue is likely with GCVideo DVI's controller tap. Yes, you are absolutely right. I forgot to mention that, sorry! Im going to use the alternate Controller connection as m...

boredomca wrote:Can you upload pictures of the mobo

Yes, I will do so either later tonite or tomorrow. Im at work currently

Thanks for the help!

Controller Port one is the most used. It's possible that the connection on the dongle is a bit worn and not making a proper connection with the worn first port. I would test with another controller, if it works fine then it's the dongle and would only require reshaping the pins I already tested it ...

Controller port 1 will not register any commands on the screen in gameplay or in the menus. With a Wavebird connected, when I press the controller buttons, it registers on the dongle that they are being pressed (the dongle illuminates), that would mean the port is getting power I would assume. Ports...