Metroid Prime not working with swiss

[Drakon]

My system is running a wiikey fusion flashed with swiss r221 and wkf firmware 1.0 for autoboot. All games run fine except for metroid prime. Metroid prime gets stuck on "reading ..."

If I first scroll to another iso like f-zero, hit "a" to get the picture and info about it, then back out, then try metroid prime, metroid prime will instead freeze at "reset base offset .." after it loads the iso.

I just loaded the swiss 0.3 r174 dol file, metroid prime runs fine from that.

Just to really illustrate the point, here's a youtube captured video of it.

http://www.youtube.com/watch?v=QMSGc0Dn ... e=youtu.be

[megalomaniac]

Check your results against r216

[Drakon]

Check your results against r216

Have a link? Here it only goes as low as 217:

viewtopic.php?f=25&t=1375

[emu_kidid]

something is screwed up, why are they all reporting a 0x00000000 sector base offset?

[Drakon]

something is screwed up, why are they all reporting a 0x00000000 sector base offset?

All I know is older builds don't have this problem so I don't think it's an issue with my hardware.

[emu_kidid]

I'll re-test on my WKF cube tomorrow, thanks for letting me know.

[Drakon]

I'll re-test on my WKF cube tomorrow, thanks for letting me know.

My pleasure. I'm using a dol 001 ipl 1.1 according to the swiss menu. I like to help people develop new solutions for classic hardware in any way I can.

[emu_kidid]

Fixed in r235.

[Drakon]

Fixed in r235.

Awesome, where do I get r235 from?

[Ashen]

If its not a major official release you have to build it yourself. Or wait for the "nightly build" to be updated.

[Drakon]

If its not a major official release you have to build it yourself. Or wait for the "nightly build" to be updated.

Wait I shall.

[piratesephiroth]

If its not a major official release you have to build it yourself. Or wait for the "nightly build" to be updated.

Wait I shall.

It's extremely easy to compile it yourself...

[GillBert]

It's extremely easy to compile it yourself...

I've just saw your compiling guide here... Very nice, I'll try it out. Thanks!

[Sizednochi]

Wait I shall.

Hahaha, kinda off-topic, but I recognize your avatar/username. You fixed up that awesome Mario Land 2 DX patch, right? Also the Metroid II full colour patch! I'd like to say thanks - I'm in debt forever.

Anyway, Metroid Prime is working fine here since r174, it's a bit heavy on loading though, so it lags quite a lot.

[NNSS32]

Hey, that happens to me with Wind Waker and Mario Kart. If I let it read for a while, then turn off the cube, the start menu will show either Wind Waker or Mario Kart (this depends on what was being read as I shut off the cube) as the inserted disk, not swiss. A minor inconvenience, but I still get to play the game, so what the heck. (A fix would be appreciated though.) On another SD card (the same type as the one I used with the long reading issue one) Mario Kart will boot up fine, but Wind Waker will still be stuck in reading limbo.

[emu_kidid]

Lag from SDGecko is to be expected. OP was talking about Wiikey Fusion

[NNSS32]

I was talking about Wiikey as well. Let me make myself clearer. In the swiss menu, if I select Mario Kart, the screen says 'reading' and never progresses from there. The only way to get out is to shut off my Gamecube. When I turn it on again, instead of the gameplay menu showing swiss as the inserted disk, the game that was previously stuck in 'reading' mode is shown as the inserted disk. When I hit start, the game runs as though nothing had happened. On a different SD card with the same games, Mario Kart does not get stuck in reading, it loads normally. However, Wind Waker still experiences this issue. Its strange, and I may document it soon. Perhaps this will help with Swiss research. Sorry for the confusion.

[megalomaniac]

I was talking about Wiikey as well. Let me make myself clearer. In the swiss menu, if I select Mario Kart, the screen says 'reading' and never progresses from there. The only way to get out is to shut off my Gamecube. When I turn it on again, instead of the gameplay menu showing swiss as the inserted disk, the game that was previously stuck in 'reading' mode is shown as the inserted disk. When I hit start, the game runs as though nothing had happened. On a different SD card with the same games, Mario Kart does not get stuck in reading, it loads normally. However, Wind Waker still experiences this issue. Its strange, and I may document it soon. Perhaps this will help with Swiss research. Sorry for the confusion.

that sounds like a WKF hardware connection issue, not swiss related

[NNSS32]

aww maan. lol ok then

[megalomaniac]

I was talking about Wiikey as well. Let me make myself clearer. In the swiss menu, if I select Mario Kart, the screen says 'reading' and never progresses from there. The only way to get out is to shut off my Gamecube. When I turn it on again, instead of the gameplay menu showing swiss as the inserted disk, the game that was previously stuck in 'reading' mode is shown as the inserted disk. When I hit start, the game runs as though nothing had happened. On a different SD card with the same games, Mario Kart does not get stuck in reading, it loads normally. However, Wind Waker still experiences this issue. Its strange, and I may document it soon. Perhaps this will help with Swiss research. Sorry for the confusion.

that sounds like a WKF hardware connection issue, not swiss related

hmmmm...after reading over your description again, im not sure what the issue could be...
one sd card works and the other doesnt...so maybe its SD related and hardware related..

note: if you power off the GC, then WKF should be powered off also but you state the previous selected iso is loaded...you better check your power supply or batteries because it sounds like the WKF continues to receive power when you switch the GC off..


also, redump your isos in case the ones you are currently using are pre-patched from an older version of swiss

[Drakon]

Wait I shall.

Hahaha, kinda off-topic, but I recognize your avatar/username. You fixed up that awesome Mario Land 2 DX patch, right? Also the Metroid II full colour patch! I'd like to say thanks - I'm in debt forever.

Anyway, Metroid Prime is working fine here since r174, it's a bit heavy on loading though, so it lags quite a lot.

Yes that's me, I found it odd that marioland 2 dx had been in a crashing state since 2006 and in a very short amount of time I figured out how to fix the bug. Myself + spikeman also got marioland full colour version going on real hardware. I don't think my non gc work belongs on this forum so you can always join my forum to see some of the other fun / crazy projects I've been involved with, the link is in my signature.

I don't think my problem is because of wiikey connectivity since I can load an older swiss.dol and the game runs fine.