GCPlug Information - Inc firmware updates
Re: GCPlug Information - Inc firmware updates
Cant even get my programmer to detect the chip, i end up with no data just $ff, I have bridged the pad so it cant be that.
Re: GCPlug Information - Inc firmware updates
I think the memory chips on Chinese GCPlugs may come from mis-labelled stock, so we don't get the right protocol when we try to communicate with them.
To those wo succeeded, what's the reference labelled on yours, and what reference the flashing software detected/used to flash it?
As GCPlug's update is made via SPI, and Gamecube has 2 or 3 SPI ports, why won't we get an updater utility on the Cube, so we just have to build the cable? Building a male SP2 connector is easy, I already did one for my SD2SP2 with a plastic tab (from a yoghurt cup edge) and adhesive metal sheet (copper), while getting all the stuff and software up and running on a PC can be such a headache.
And why would we need to short the pads when writing to the chip with a 8pin SOIC clip? Doesn't the clip do its job?
To those wo succeeded, what's the reference labelled on yours, and what reference the flashing software detected/used to flash it?
As GCPlug's update is made via SPI, and Gamecube has 2 or 3 SPI ports, why won't we get an updater utility on the Cube, so we just have to build the cable? Building a male SP2 connector is easy, I already did one for my SD2SP2 with a plastic tab (from a yoghurt cup edge) and adhesive metal sheet (copper), while getting all the stuff and software up and running on a PC can be such a headache.
And why would we need to short the pads when writing to the chip with a 8pin SOIC clip? Doesn't the clip do its job?
DMG/MultiFreq OC/EDGB/EZF Jr, AGB/SC miniSD, NTR/NeoMK3, USG/flashme V8/SC miniSD
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
Re: GCPlug Information - Inc firmware updates
Hello guys, I am new on this forum.
First of all, thank you everyone for all the support, information I found here. I just wanted to let you know that I have recently bought a GCPlug on AliExpress (arrived this week) and the firmware was version 3.0a which means that it should be possible to get it updated easily with any homebrew launcher like Swiss. I know some of you struggled to get their GCPlug updated to a 3.X version with an hardware solution, you might be interested by this.
If ever, you are in the same situation than me, let me know if you succeed to update it with the .dol file because it did not worked, nothing happen when I boot the .dol file and I go to the update menu on the GCPlug. It did not recognise the firmware. I have also noticed that it is not possible to access to the GCPlug menu through the controller by holding L, R, X, Y. Did someone experienced the same thing ? I don’t know if all of this is due to the hardware solution used on the plug ?!
First of all, thank you everyone for all the support, information I found here. I just wanted to let you know that I have recently bought a GCPlug on AliExpress (arrived this week) and the firmware was version 3.0a which means that it should be possible to get it updated easily with any homebrew launcher like Swiss. I know some of you struggled to get their GCPlug updated to a 3.X version with an hardware solution, you might be interested by this.
If ever, you are in the same situation than me, let me know if you succeed to update it with the .dol file because it did not worked, nothing happen when I boot the .dol file and I go to the update menu on the GCPlug. It did not recognise the firmware. I have also noticed that it is not possible to access to the GCPlug menu through the controller by holding L, R, X, Y. Did someone experienced the same thing ? I don’t know if all of this is due to the hardware solution used on the plug ?!
DOL001(EUR)/GCPlug/SD2SP2/Softmod
Re: GCPlug Information - Inc firmware updates
I just received my gcplug with 3.0a firmware from aliexpress and i successfully updated it to 3.0e from swiss launching the 3.0e dol
Re: GCPlug Information - Inc firmware updates
My gcplug arrived but apparently it doesn't work. I already cleaned the digital output! I already opened the console and saw nothing wrong. I changed the cable and nothing changes. My gamecube is DOL-002 and works well with the analog output. Could it be a defect in my gamecube or a defect in gcplug or am I doing something wrong? How to know? Help please!!
Sorry, I don't write in english very well.
Sorry, I don't write in english very well.
Re: GCPlug Information - Inc firmware updates
GCVideo-DVI struggles with PAL-M, you need software outputting NTSC.
Re: GCPlug Information - Inc firmware updates
Can be this software the swiss?
Re: GCPlug Information - Inc firmware updates
Yeah, I've made the necessary change in r906 and later.
Re: GCPlug Information - Inc firmware updates
Thank you very very much!!! It is working!!! I m very happy!!!
Re: GCPlug Information - Inc firmware updates
Hi! Is it possible to change ipl from pal m to ntsc only by software?
Re: GCPlug Information - Inc firmware updates
Ok. Thank you!
Re: GCPlug Information - Inc firmware updates
Just wanted to add I managed to update mine too using the dol, something I wouldn't expect to work. Got mine for €35 which is an absolute bargain.
"The only thing more dangerous than a hardware guru with a code patch is a programmer with a soldering iron."
Re: GCPlug Information - Inc firmware updates
Extrems> With launching through IPL, can one get correct display on PAL-M consoles, or does it re-launch from internal rom, without those specific NTSC video patches?
There is a new GC-video plug and play, that seems to have the carby quality level, with metal surrounded plug, and not 3D print case, at a lower price.
There is a new GC-video plug and play, that seems to have the carby quality level, with metal surrounded plug, and not 3D print case, at a lower price.
DMG/MultiFreq OC/EDGB/EZF Jr, AGB/SC miniSD, NTR/NeoMK3, USG/flashme V8/SC miniSD
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
Re: GCPlug Information - Inc firmware updates
It's patched to NTSC.
Re: GCPlug Information - Inc firmware updates
Congratulations!! The New version of swiss help me very much!!Chaves wrote: ↑Mon Sep 21, 2020 3:43 pmMy gcplug arrived but apparently it doesn't work. I already cleaned the digital output! I already opened the console and saw nothing wrong. I changed the cable and nothing changes. My gamecube is DOL-002 and works well with the analog output. Could it be a defect in my gamecube or a defect in gcplug or am I doing something wrong? How to know? Help please!!
Sorry, I don't write in english very well.
Sorry to return this subject. My gcplug is working!
But my gamecube is PAL M, so my solution was lauching by analogic output and when swiss starts, I use digital output with gcplug. But it is boring!! (I use exploit!)
Is there other solution?
Can I convert to ntsc (hardware changes)? Is it hard?
Re: GCPlug Information - Inc firmware updates
Your best bet would be to use an exploit that doesn't need any menu browsing, such as the Zelda ones, so you don't have to see what's happening befor SWISS is loaded.
Otherwise, get an extra NTSC or PAL cube.
Otherwise, get an extra NTSC or PAL cube.
DMG/MultiFreq OC/EDGB/EZF Jr, AGB/SC miniSD, NTR/NeoMK3, USG/flashme V8/SC miniSD
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
Re: GCPlug Information - Inc firmware updates
Ok. Thanks! I use 007 underfire. I have to click load. Really I need to see the menu.
Well, I have always wished a indigo cube.... maybe...
Well, I have always wished a indigo cube.... maybe...
Re: GCPlug Information - Inc firmware updates
Hello all,
I'm just re-opening this discussion since I saw some of you have been able to update their GCPlug with the .dol updater from GCVideo.
I understood a fix have been made on Swiss since r906. I did not catch if the fix has been made to make the updater works on PAL Gamecube or just to fix some display issues ?
Personally, I never had any issues to make the GCPlug work on my Gamecube, it is just the updater tool that always show "No compatible firmware found" despite the fact I open the correct menu on the plug and launch the .dol on Swiss.
I use the Mario Sunshine Exploit to run Swiss. I don't know if Softmod exploits have limitations.... Does anyone have an idea ?
Thanks for all.
I'm just re-opening this discussion since I saw some of you have been able to update their GCPlug with the .dol updater from GCVideo.
I understood a fix have been made on Swiss since r906. I did not catch if the fix has been made to make the updater works on PAL Gamecube or just to fix some display issues ?
Personally, I never had any issues to make the GCPlug work on my Gamecube, it is just the updater tool that always show "No compatible firmware found" despite the fact I open the correct menu on the plug and launch the .dol on Swiss.
I use the Mario Sunshine Exploit to run Swiss. I don't know if Softmod exploits have limitations.... Does anyone have an idea ?
Thanks for all.
DOL001(EUR)/GCPlug/SD2SP2/Softmod
Re: GCPlug Information - Inc firmware updates
What's your current GCplug FW version?
DMG/MultiFreq OC/EDGB/EZF Jr, AGB/SC miniSD, NTR/NeoMK3, USG/flashme V8/SC miniSD
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
Re: GCPlug Information - Inc firmware updates
The firmware is 3.0a
DOL001(EUR)/GCPlug/SD2SP2/Softmod
Re: GCPlug Information - Inc firmware updates
I’ve just received a feedback from the GCvideo dev. It seems my GCPlug firmware has been modified from the original one which makes the updater tool not compatible… I bought mine from AliExpress (model with blue plastic cover). Which model do you use guys ?
DOL001(EUR)/GCPlug/SD2SP2/Softmod
Re: GCPlug Information - Inc firmware updates
Sounds about right. The firmware was complied by different people as it wasn't being complied and posted in the main repo until some later 3.0 firmware. It may not be a deliberate modification and it's possible the only difference would be the HWID number that was chosen doesn't match up with what's on the updater.
I'd reprogram it with an external SPI programmer.
I'd reprogram it with an external SPI programmer.
Re: GCPlug Information - Inc firmware updates
Same model as yours, but stuck to 2,4x as long as I don't find a SPI programmer able to flash it correctly.
DMG/MultiFreq OC/EDGB/EZF Jr, AGB/SC miniSD, NTR/NeoMK3, USG/flashme V8/SC miniSD
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
DOL001(EUR)/RGB/GCPlug/GBP/SD2SP2, RVL 001(EUR)/RGB/CMP/WiiSD
Zelda WW with Tingle Tuner in split screen was what the GC RF modulator was made for! (Video)
Re: GCPlug Information - Inc firmware updates
I've finally been able to get my GCPlug updated.
The issue was exactly the one suspected. The original firmware was modified from ikorb project.
GCPlug is based on Citrus3000psi and Unseen project and I found the right place to get the file :
Project : https://www.printables.com/fr/model/141 ... dmi-dongle
Firmwares : http://dansprojects.com/firmware/GCPlug/
As mine was in 3.0a, I was able to use the updated-3.1.dol file and it worked !
By the way, thank you for your reply and may be this issue will help others guys who are in the same situation.
Papy.G : if one day you are able to get a SPI programmer you can find the .bin files to reprogram yours.
The issue was exactly the one suspected. The original firmware was modified from ikorb project.
GCPlug is based on Citrus3000psi and Unseen project and I found the right place to get the file :
Project : https://www.printables.com/fr/model/141 ... dmi-dongle
Firmwares : http://dansprojects.com/firmware/GCPlug/
As mine was in 3.0a, I was able to use the updated-3.1.dol file and it worked !
By the way, thank you for your reply and may be this issue will help others guys who are in the same situation.
Papy.G : if one day you are able to get a SPI programmer you can find the .bin files to reprogram yours.
DOL001(EUR)/GCPlug/SD2SP2/Softmod