Game Boy Interface

[Weario]

If there's no latency, it's odd there's a noticeable echo.

I wasn't clear enough, apologies. I meant that my receiver does not produce any additional latency.

It may or may not be a trustworthy test, but I 'benchmark' this using my Wii U and the gamepad. When I play a game like Smash Bros, or Mario Kart (which produce sound from both the receiver and the gamepad), the sounds are perfectly in sync. There's absolutely no echo.
When I play GBA multiplayer games like Four Swords or Super Mario Bros with a friend (I play using GBI SR, my friend has a real GBA), there's a noticible echo going on, which must be the 8-16ms audio lag that GBI has.
I bought this receiver not only for the better sound, but also because my LG tv has HORRIBLE sound delay (video seems to be perfect, luckily).

Hope this clears thing up!

EDIT: Also, I may be very sensitive to delays, but I can also hear the difference in audio delays when comparing GBI SR to a real GBA. I especially notice this when navigating through menus (which produce little navigation sounds) or when jumping in Wario Land 3.

[Papy.G]

it may be that the WiiU has buffers to anticipate the TV's Lag.

I just checked, my TV doesn't add lag to the inputs, only to the Broadcasts.

[Brendle]

I started using this software yesterday, great stuff thank you! Is there a way to make and use custom borders?

Thank you for your time.

[MarioMania]

You know what's missing from the GBi Software

Have a option to eject the Game & Put in another Game without turning the GameCube off

[Extrems]

Been there since day one. Use the reset button.

[MarioMania]

I know about the Reset Button

Do it like the Game Boy Software on the Nintendo one

Like "Change Game Pak"

[Extrems]

That's coming with the eventual GUI, but you still don't have to turn off with the way it currently is.

[MarioMania]

I did the autoexec

I have a old 1 GB Card just for the GBi

[Extrems]

I don't understand. Just press the reset button. You can also press B, X and Start/Pause on a controller to do the same.

[MarioMania]

Well seeing Game Boy/Color Have a Battery in them, Removing the Cart while it's on can Erase your file

Just be safe, Now with GBA Games, I don't know

[Extrems]

Keep holding the reset button while swapping then.

[MarioMania]

I will do that

Next Update can you please do a Control Config

I use mostly my SNES Controller

Like B&A = Y&B

Z to open to ajust the screen size, take a pic

[KentaZX]

So I've been settings up the GBI HF with my GC video HDMI modded gamecube, and while my TV doe not like 240p, The image quality is pretty much perfect but I was wondering if its possible to scale it up a bit or have a way to fill up the screen more? I've heard something about the CLi files being configurable but I don't know how to open those files up. Can anyone help me out on this? If its not possible atm, then is it possible to use borders in the HF edition? If so, how do I get them to work?

Also, I've accessed swiss by the windwaker exploit, if that needs to be known.

[Extrems]

You're not using the right edition for HDMI to a TV.

[KentaZX]

Okay so I'm, checking the standard edition right now, but I can't seem to get it sharp as the HF edition was.. the text just seems too soft...

I've been setting the standard edition to 480p NTSC and either 3:2 or 4:3 aspect ration with the scale2xEX filter so far...is there a better suggestion than this? I've tried loading up 240p instead of 480p but my TV just doesn't like that resolution apparently.

Also I've just check im in GCVideo DVI 2.3. Could this also be the cause of my problems?

[Extrems]

Try the GCHD preset, but of course it's not going to be as sharp if you're applying Scale2xEx.

I recommend getting your firmware upgraded.

[KentaZX]

and how do I enable the GCHD preset? do I have to open the Cli files somehow (because I do not know how to do that, never done it before)?

OR do I just need to have those files in my SD card and put on these settings before booting up Gbi:

--aspect=16:9
--offset=+4:-2
--zoom=3
--format=ntsc
--scan-mode=non-progressive

[Extrems]

You just load the gbi-gchd.dol+cli or gbisr-gchd.dol+cli file.

[KentaZX]

Okay so i updated the swiss, and then when I loaded that file, my TV says "Mode not supported" Apparently. so I lost the signal there...

[Weario]

KEntaZX, I think these settings could work for you, use the GBI SR edition with these values:

Code: Select all

--zoom=2:3
--format=size=568
--scan-mode=progressive
--no-overlay
--scaler=nearest
--matrix=identity

With your firmware version, I think this should display on your tv just fine. Make sure your tv is not over-scanning the picture. (so look for settings like 'just-scan')

[Extrems]

This won't produce as good quality as the GCHD preset set to 480p rather than 960i. It's not a firmware issue.

[Weario]

This won't produce as good quality as the GCHD preset set to 480p rather than 960i. It's not a firmware issue.

Ahh yes, I see that the Wiki has been updated since I last used it. I recall using settings that were only compatible with gcvideo 2.4d, but I suppose that's old info by now. (or maybe it's never been that case and I read it all wrong)

[KentaZX]

This won't produce as good quality as the GCHD preset set to 480p rather than 960i. It's not a firmware issue.

wait, if the GCHD preset sets to 480p, then how come I get a "mode not supported" error on my TV? I was able to set to 480p just fine before with the standard and the HF edition....does the GCHD preset uses HD60 instead of NTSC? If so then thats probably why it wont work on me. Because whenever I tried on the standard edition to switch from NTSC to HD60, I just lose the signal.

[Extrems]

wait, if the GCHD preset sets to 480p, then how come I get a "mode not supported" error on my TV? I was able to set to 480p just fine before with the standard and the HF edition....does the GCHD preset uses HD60 instead of NTSC? If so then thats probably why it wont work on me. Because whenever I tried on the standard edition to switch from NTSC to HD60, I just lose the signal.

I said it sets 960i. HD60 is generally not compatible with GCVideo.

[KentaZX]

Oh. so does that mean I'm SOL for now? Or is there a way to open the Dol+ ClI file so I can set it to 480p and NTSC?